FourWheelForum
>
Search Forums
Search Results
User Name
Remember Me?
Password
FAQ
Members List
Calendar
Today's Posts
Search
Search Forums
Show Threads
Show Posts
Tag Search
Advanced Search
Go to Page...
Showing results 1 to 11 of 11
Search took
0.01
seconds.
Search:
Posts Made By:
ghoti10
Forum:
The Honda CA95 / Benly 150 Restoration
03-23-2011, 05:49 PM
Replies:
5
Clutch adjustment
Views:
9,693
Posted By
ghoti10
Ok, the clutch plates are new. The lifter rod is...
Ok, the clutch plates are new. The lifter rod is supposed to have one rounded end and one flat end, Yes? With the round end fitting into the clutch lifter joint. The springs were within...
Forum:
The Honda CA95 / Benly 150 Restoration
03-22-2011, 05:34 PM
Replies:
5
Clutch adjustment
Views:
9,693
Posted By
ghoti10
Thanks for the quick response. Now for the sake...
Thanks for the quick response. Now for the sake of discussion lets say the clutch adjuster had been cleaned and repacked with new grease and the problem still existed. Step 2?
Forum:
The Honda CA95 / Benly 150 Restoration
03-20-2011, 06:07 PM
Replies:
5
Clutch adjustment
Views:
9,693
Posted By
ghoti10
Clutch adjustment
I haven't seen this particular question about the clutches on these things so here it goes. When I torque the 4 bolts on the clutch lifter plate to specs, I cannot squeeze the clutch lever. I then...
Forum:
The Honda CA95 / Benly 150 Restoration
11-11-2009, 05:19 PM
Replies:
1
cylinder head /breather gaskets
Views:
7,535
Posted By
ghoti10
cylinder head /breather gaskets
Does anyone have photos of the cylinder head/breather cover gaskets and the order that they are installed? I think I have them but one seems to be a metal plate with a few holes. Thank you very...
Forum:
The Honda CA95 / Benly 150 Restoration
08-11-2009, 06:35 PM
Replies:
12
ca 95 timing question
Views:
17,666
Posted By
ghoti10
Thanks much RobG. My cam sprocket mark is at...
Thanks much RobG. My cam sprocket mark is at 12:00 but the crankshaft mark is at 6:00, as far apart as possible. I'll change the position when I get time. I understand that 180 out just changes...
Forum:
The Honda CA95 / Benly 150 Restoration
07-26-2009, 05:39 PM
Replies:
12
ca 95 timing question
Views:
17,666
Posted By
ghoti10
Ok, I took the cam sprocket off and made sure it...
Ok, I took the cam sprocket off and made sure it was bolted in properly. I made sure the cam sprocket timing mark was at the top of the sprocket and the timing mark on the crankshaft sprocket was at...
Forum:
The Honda CA95 / Benly 150 Restoration
07-25-2009, 07:52 AM
Replies:
12
ca 95 timing question
Views:
17,666
Posted By
ghoti10
Ok, here,s a couple shots of what I was talking...
Ok, here,s a couple shots of what I was talking about last night.The first one shows cam sprocket mark on the top while the rotor mark is lined up with the "T". The second shot shows the alignment...
Forum:
The Honda CA95 / Benly 150 Restoration
07-24-2009, 04:26 PM
Replies:
12
ca 95 timing question
Views:
17,666
Posted By
ghoti10
The photo shows the cam sprocket timing mark on...
The photo shows the cam sprocket timing mark on the top. At the same point the "T" on the crank is lined up with the timing mark on the rotor and both pistons are at tdc or very close. I can...
Forum:
The Honda CA95 / Benly 150 Restoration
07-23-2009, 06:32 PM
Replies:
12
ca 95 timing question
Views:
17,666
Posted By
ghoti10
In a related timing question...is it possible to...
In a related timing question...is it possible to bolt the cam sprocket to the wrong holes? There's supposed to be a difference in the spacing of the 3 bolt holes but I can't see it in my motor. But...
Forum:
The Honda CA95 / Benly 150 Restoration
05-16-2009, 06:47 AM
Replies:
6
ignition switch questions?
Views:
11,189
Posted By
ghoti10
I found the parts manual here ...
I found the parts manual here http://downloads.hondatech.info/Moto/CA/CA95_Parts_Manual.pdf Page 43 is the wiring diagram. It's a good source of information but it's not the shop manual. I'm...
Forum:
The Honda CA95 / Benly 150 Restoration
05-12-2009, 04:58 PM
Replies:
6
ignition switch questions?
Views:
11,189
Posted By
ghoti10
ignition switch questions?
I've hit the wall with this one. It's a early 60's ca95 barn find. I had to replace the ignition switch and part of the wiring harness. Now when I hook up the battery, the brake light comes...
Showing results 1 to 11 of 11
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
Website News & Updates
Forum Operations
Events & Happenings
Additional Projects Area
Motorcycle Stuff For Sale
Motorcycle Parts Wanted
Dirtbikes New & Old
Motorcycles & Streetbikes!
The Honda CA95 / Benly 150 Restoration
Aprilia Mille RSVR - 1st Generation
Yamaha WR200 Dual Sport Dirtbike
The Kawasaki Triple H1 and H2
Cool Motorcycle Pictures & Stuff
Honda Superhawk 250 / CB72
1969 Honda CL70 Scrambler!
Honda CL175 1968-1973
Honda Dream CA160
Ducati 250 Sebring / Mach I Restoration
KTM 400 EXC Dual Sport
2005 Suzuki (Kawasaki) RMZ 250 Motocross
Buco Saddlebags Repair and Help Topics
Truck Talk
LEXUS 1UZ-FE Engine Swap
1UZ-FE Tuning and Mods
Dodge 2500 Diesel Talk
Tire & Suspension Talk
Transmission & Other Stuff
Other Truck Chat
Car Chat
2000 Honda Prelude Rebuild
2003 Audi 3.0L Quattro - B6
1979 MGB - The Orange Roadster!
Any other car talk
Tools, Electronics & Stereo Stuff
Restoration & Fabrication Techniques
Tools, Machines and Shop Toys
Technology & Electronics
All times are GMT -8. The time now is
07:23 AM
.
Contact Us
-
Fourwheelforum.com
-
Archive
-
Top
Powered by vBulletin® Version 3.7.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.